View GS71116TJ_1023734.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

GS71116TP/J/U SOJ, TSOP, FP-BGA Commercial Temp Industrial Temp Features
* Fast access time: 10, 12, 15ns * CMOS low power operation: 100/85/70 mA at min. cycle time. * Single 3.3V 0.3V power supply * All inputs and outputs are TTL compatible * Byte control * Fully static operation * Industrial Temperature Option: -40 to 85C * Package line up J: 400mil, 44 pin SOJ package TP: 400mil, 44 pin TSOP Type II package U: 6 mm x 8 mm Fine Pitch Ball Grid Array package
64K x 16 1Mb Asynchronous SRAM
SOJ 64K x 16 Pin Configuration
A4 A3 A2 A1 A0 CE DQ1 DQ2 DQ3 DQ4 VDD VSS DQ5 DQ6 DQ7 DQ8 WE A15 A14 A13 A12 NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
10, 12, 15ns 3.3V VDD Center VDD & VSS
Top view
Description
The GS71116 is a high speed CMOS static RAM organized as 65,536-words by 16-bits. Static design eliminates the need for external clocks or timing strobes. Operating on a single 3.3V power supply and all inputs and outputs are TTL compatible. The GS71116 is available in a 6x8 mm Fine Pitch BGA package as well as in 400 mil SOJ and 400 mil TSOP Type-II packages.
Pin Descriptions Symbol
A0 to A15 DQ1 to DQ16 CE LB UB WE OE VDD VSS NC
Description
Data input/output
Chip enable input
w
w
w
Lower byte enable input (DQ1 to DQ8) Upper byte enable input (DQ9 to DQ16) Write enable input Output enable input +3.3V power supply Ground No connect
.D
Address input
t a
S a
e h
t e
A B C D E F G H
U 4
19 20 21 22
.c
SOJ
44 pin
m o
27 26 25 24 23
44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28
A5 A6 A7 OE UB LB DQ16 DQ15 DQ14 DQ13 VSS VDD DQ12 DQ11 DQ10 DQ9 NC A8 A9 A10 A11 NC
Fine Pitch BGA 64K x 16 Bump Configuration
1 2 3 4 5 6
LB DQ16
OE UB
A0 A3 A5 NC NC A8 A10 A13
A1 A4 A6 A7 NC A9 A11 A14
A2 CE DQ2 DQ4 DQ5 DQ7 WE A15
NC DQ1 DQ3 VDD VSS
DQ14 DQ15 VSS VDD DQ13 DQ12
DQ9 NC
NC A12
DQ8 NC
6mm x 8mm, 0.75mm Bump Pitch Top View Rev: 1.06 6/2000 1/15 (c) 1999, Giga Semiconductor, Inc.
M
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
www..com
DQ11 DQ10
DQ6
GS71116TP/J/U
TSOP-II 64K x 16 Pin Configuration
A4 A3 A2 A1 A0 CE DQ1 DQ2 DQ3 DQ4 VDD VSS DQ5 DQ6 DQ7 DQ8 WE A15 A14 A13 A12 NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A5 A6 A7 OE UB LB DQ16 DQ15 DQ14 DQ13 VSS VDD DQ12 DQ11 DQ10 DQ9 NC A8 A9 A10 A11 NC
Top view
44 pin TSOP II
Block Diagram
A0 Address Input Buffer
Row Decoder
Memory Array
A15 CE WE Control OE _____ UB LB _____
Column Decoder
I/O Buffer
DQ1
DQ16
Rev: 1.06 6/2000
2/15
(c) 1999, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS71116TP/J/U
Truth Table CE
H
OE
X
WE
X
LB
X L
UB
X L H L L H L X H
DQ1 to DQ8
Not Selected Read Read High Z Write Write Not Write, High Z High Z High Z
DQ9 to DQ16
Not Selected Read High Z Read Write Not Write, High Z Write High Z High Z
VDD Current
ISB1, ISB2
L
L
H
L H L
L
X
L
L H
IDD
L L
H X
H X
X H
Note: X: "H" or "L"
Absolute Maximum Ratings
Parameter
Supply Voltage Input Voltage Output Voltage Allowable power dissipation Storage temperature
Symbol
VDD VIN VOUT PD TSTG
Rating
-0.5 to +4.6 -0.5 to VDD+0.5 ( 4.6V max.) -0.5 to VDD+0.5 ( 4.6V max.) 0.7 -55 to 150
Unit
V V V W
oC
Note: Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation shall be restricted to Recommended Operating Conditions. Exposure to higher than recommended voltages for extended periods of time could affect device reliability.
Rev: 1.06 6/2000
3/15
(c) 1999, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS71116TP/J/U Recommended Operating Conditions
Parameter
Supply Voltage for -12/15 Supply Voltage for -10 Input High Voltage Input Low Voltage Ambient Temperature, Commercial Range Ambient Temperature, Industrial Range
Symbol
VDD VDD VIH VIL TAc TAI
Min
3.0 3.135 2.0 -0.3 0 -40
Typ
3.3 3.3 -
Max
3.6 3.6 VDD+0.3 0.8 70 85
Unit
V V V V
o
C C
o
Note: 1. Input overshoot voltage should be less than VDD+2V and not exceed 20ns. 2. Input undershoot voltage should be greater than -2V and not exceed 20ns.
Capacitance
Parameter
Input Capacitance Output Capacitance
Symbol
CIN COUT
Test Condition
VIN=0V VOUT=0V
Max
5 7
Unit
pF pF
Notes: 1. Tested at TA=25C, f=1MHz 2. These parameters are sampled and are not 100% tested
DC I/O Pin Characteristics
Parameter
Input Leakage Current Output Leakage Current Output High Voltage Output Low Voltage
Symbol
IIL ILO VOH VOL
Test Conditions
VIN = 0 to VDD Output High Z VOUT = 0 to VDD IOH = - 4mA ILO = + 4mA
Min
-1uA -1uA 2.4
Max
1uA 1uA
0.4V
Rev: 1.06 6/2000
4/15
(c) 1999, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS71116TP/J/U Power Supply Currents
0 to 70C Parameter Symbol Test Conditions 10ns
Operating Supply Current CE VIL All other inputs VIH or VIL Min. cycle time IOUT = 0 mA CE VIH All other inputs VIH or VIL Min. cycle time CE VDD - 0.2V All other inputs VDD - 0.2V or 0.2V
-40 to 85C 15ns 10ns 12ns 15ns
12ns
IDD (max)
100mA
85mA
70mA
115mA
100mA
85mA
Standby Current
ISB1 (max)
45mA
40mA
35mA
50mA
45mA
40mA
Standby Current
ISB2 (max)
10mA
15mA
Rev: 1.06 6/2000
5/15
(c) 1999, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS71116TP/J/U AC Test Conditions
Parameter
Input high level Input low level Input rise time Input fall time Input reference level Output reference level Output load
Conditions
VIH=2.4V VIL=0.4V tr=1V/ns tf=1V/ns 1.4V 1.4V Fig. 1& 2
Output Load 1
DQ 50 VT=1.4V 30pF1
Output Load 2
3.3V DQ 5pF1 589 434
Note: 1. Include scope and jig capacitance. 2. Test conditions as specified with output loading as shown in Fig. 1 unless otherwise noted 3. Output load 2 for tLZ, tHZ, tOLZ and tOHZ.
Rev: 1.06 6/2000
6/15
(c) 1999, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS71116TP/J/U AC Characteristics
Read Cycle Parameter
Read cycle time Address access time Chip enable access time (CE) Byte enable access time (UB, LB) Output enable to output valid (OE) Output hold from address change Chip enable to output in low Z (CE) Output enable to output in low Z (OE) Byte enable to output in low Z (UB, LB) Chip disable to output in High Z (CE) Output disable to output in High Z (OE) Byte disable to output in High Z (UB, LB) * These parameters are sampled and are not 100% tested
Symbol
tRC tAA tAC tAB tOE tOH tLZ* tOLZ* tBLZ* tHZ* tOHZ* tBHZ*
-10 Min
10 --------3 3 0 0 -------
-12 Max
--10 10 4 4 --------5 4 3.5
-15 Max
--12 12 5 5 --------6 5 3.5
Min
12 --------3 3 0 0 -------
Min
15 --------3 3 0 0 -------
Max
--15 15 6 6 --------7 6 4
Unit
ns ns ns ns ns ns ns ns ns ns ns ---
Read Cycle 1: CE = OE = VIL, WE = VIH, UB and, or LB = VIL
tRC Address tAA tOH Data Out Previous Data Data valid
Rev: 1.06 6/2000
7/15
(c) 1999, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS71116TP/J/U
Read Cycle 2: WE = VIH
tRC Address tAA CE tAC tLZ UB, LB OE tBLZ tOE Data Out tOLZ High impedance tAB tBHZ tOHZ Data valid tHZ
Write Cycle Parameter
Write cycle time Address valid to end of write Chip enable to end of write Byte enable to end of write Data set up time Data hold time Write pulse width Address set up time Write recovery time (WE) Write recovery time (CE) Output Low Z from end of write Write to output in High Z * These parameters are sampled and are not 100% tested
Symbol
tWC tAW tCW tBW tDW tDH tWP tAS tWR tWR1 tWLZ* tWHZ*
-10 Min
10 7 7 7 5 0 7 0 0 0 3 ---
-12 Max
----------------------4
-15 Max
----------------------5
Min
12 8 8 8 6 0 8 0 0 0 3 ---
Min
15 10 10 10 7 0 10 0 0 0 3 ---
Max
----------------------6
Unit
ns ns ns ns ns ns ns ns ns ns ns ns
Rev: 1.06 6/2000
8/15
(c) 1999, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS71116TP/J/U
Write Cycle 1: WE control
tWC Address tAW OE tCW CE tBW UB, LB tAS WE tDW Data In tWHZ Data Out tDH Data valid tWLZ High impedance tWP tWR
Write Cycle 2: CE control
tWC Address tAW OE tAS CE tBW UB, LB tWP WE tDW Data In Data Out tDH Data valid tCW tWR1
High impedance
Rev: 1.06 6/2000
9/15
(c) 1999, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS71116TP/J/U
Write Cycle 3: UB, LB control
tWC Address tAW OE tAS CE tBW UB, LB tWP WE tDW Data In Data Out tDH Data valid tCW tWR1
High impedance
Rev: 1.06 6/2000
10/15
(c) 1999, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS71116TP/J/U
44 Pin, 400 mil SOJ Symbol
A A1 A2 HE GE E B B1 1 e 22
A
D 44 23
L c
Dimension in inch min nom max
0.025 0.018 0.008 0.148 -
Dimension in mm min nom max
0.635 2.667 0.660 28.44 9.144 2.083 0o 2.794 0.457 0.711 0.203 28.58 1.27 9.398 2.210 3.759 2.921 0.813 28.70 9.652 2.70 0.102 7o
0.105 0.110 0.115 0.026 0.028 0.032 1.120 1.125 1.130 0.05 -
c D E e
0.395 0.400 0.405 10.033 10.160 10.287 0.435 0.440 0.445 11.049 11.176 11.303 0.360 0.370 0.380 0.082 0.087 0.106 0o 0.004 7o
A
A2
A1
y
B B1 Detail A
HE Q GE L y Q
Note: 1. Dimension D& E do not include interlead flash 2. Dimension B1 does not include dambar protrusion / intrusion
Rev: 1.06 6/2000
11/15
(c) 1999, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS71116TP/J/U
44 Pin, 400 mil TSOP-II Dimension in inch Dimension in mm Symbol min nom max min nom max
A A1 HE
A
44
D
23
c
0.002 0.01 -
-
0.047 -
0.05 0.95 0.25 -
1.00 0.35 0.15
1.20 1.05 0.45 -
E
A2 B c D E e HE L
0.037 0.039 0.041 0.014 0.018 0.006 -
1 A2
e
22 B
0.721 0.725 0.729 18.31 18.41 18.51 0.396 0.400 0.404 10.06 10.16 10.26 0.031 0.40 0
o
0.80 0.50 0.80 -
0.60 0.10 5o
A
0.455 0.463 0.471 11.56 11.76 11.96 0.016 0.020 0.024 0
o
A1
y L1 L
L1 y Q
0.031 -
0.004 5
o
Detail A
Q
Note: 1. Dimension D& E do not include interlead flash 2. Dimension B does not include dambar protrusion / intrusion 3. Controlling dimension: mm
Rev: 1.06 6/2000
12/15
(c) 1999, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS71116TP/J/U 6mm x 8mm Fine Pitch BGA
8.00 0.10 6.00 0.10 0.22 0.05 3 2 1 6 0.75(typ).
13/15 (c) 1999, Giga Semiconductor, Inc.
Top View
1.20(max)
pin A1 index
Bottom View
pin A1 index
5
4
Rev: 1.06 6/2000
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Ball Dia. 0.35 Pitch 0.75
3.75 5.25
0.36(typ)
0.10
G
C
D
H
A
B
E
F
D
units: mm
GS71116TP/J/U
Ordering Information Part Number*
GS71116TP-10 GS71116TP-12 GS71116TP-15 GS71116TP-10I GS71116TP-12I GS71116TP-15I GS71116J-10 GS71116J-12 GS71116J-15 GS71116J-10I GS71116J-12I GS71116J-15I GS71116U-10 GS71116U-12 GS71116U-15 GS71116U-10I GS71116U-12I GS71116U-15I
*
Package
400 mil TSOP-II 400 mil TSOP-II 400 mil TSOP-II 400 mil TSOP-II 400 mil TSOP-II 400 mil TSOP-II 400 mil SOJ 400 mil SOJ 400 mil SOJ 400 mil SOJ 400 mil SOJ 400 mil SOJ Fine Pitch BGA Fine Pitch BGA Fine Pitch BGA Fine Pitch BGA Fine Pitch BGA Fine Pitch BGA
Access Time
10 ns 12 ns 15 ns 10 ns 12 ns 15 ns 10 ns 12 ns 15 ns 10 ns 12 ns 15 ns 10 ns 12 ns 15 ns 10 ns 12 ns 15 ns
Temp. Range
Commercial Commercial Commercial Industrial Industrial Industrial Commercial Commercial Commercial Industrial Industrial Industrial Commercial Commercial Commercial Industrial Industrial Industrial
Status
Customers requiring delivery in Tape and Reel should add the character "T" to the end of the part number. For example: GS71116TP-10T
Rev: 1.06 6/2000
14/15
(c) 1999, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
GS71116TP/J/U Revision History
Rev. Code: Old; New
GS711Rev1.05 10/19991/ 2000K;Rev 5 2/2000L GS71116 Rev 1.05 2/2000;Rev1.06 2/2000M (not posted) GS71116 Rev1.05 2/2000; Rev1.06 6/2000 (previous rev not posted)
Types of Changes Page #/Revisions/Reason Format or Content
Format/Content Content Content 1. 2. 1. 2. 1. 2. GSI Logo Took all referenced to 8ns and 9ns speed bins out. Heading, Power Supply Currents, Read and Writ eCycle table, Ordering information. Added Standby Current numbers back into Power Supply Currents table Noted that numbers were max.
Rev: 1.06 6/2000
15/15
(c) 1999, Giga Semiconductor, Inc.
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.

▲Up To Search▲

Price & Availability of GS71116TJ

	To Download GS71116TJ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .